Photoincat 2 IPv6 PPPoE

来自Photonicat Wiki
跳转到导航 跳转到搜索
适用版本 / Applies to photonicatWrt 26.04.1 (r7720, OpenWrt 24+ base, fw4/nftables, odhcpd) — 更新于 2026-07 / Updated 2026-07
旧版指南 / Older firmware 2023–2024 固件请参考本页面历史版本 / For 2023–2024 firmware see the page history
  • 本文说明如何在 photonicat (photonicatWrt 26.04.x) 上配置基于 PPPoE 的原生 IPv6，让内网设备通过 SLAAC / DHCPv6 获得公网 (GUA) 地址，全球直连、无需 NAT6。
  • This document explains how to configure native IPv6 over PPPoE on photonicat (photonicatWrt 26.04.x), so LAN clients get global (GUA) addresses via SLAAC / DHCPv6 — direct global connectivity, no NAT6 required.

一键配置脚本 / Automatic setup script

无需手动执行下面的步骤，可以直接运行一键脚本自动完成全部配置（自动备份、应用、验证）。 / Instead of the manual steps below, you can run a one-shot script that applies all of them for you (backup, apply, verify).

SSH 登录路由器后运行 / SSH into the router and run: 

cd /tmp
wget -O pcat2_pppoe_ipv6.sh https://gist.githubusercontent.com/c2h2/ae07a4c818457b4cf3f087bf164059f8/raw/pcat2_pppoe_ipv6.sh
sh pcat2_pppoe_ipv6.sh
  • 脚本会先把当前配置备份到 /tmp，应用时 PPPoE 会短暂断线重连几秒，随后自动等待前缀下发并测试 IPv6 连通性。 / The script backs up your config to /tmp first, briefly restarts the PPPoE session, then waits for the delegated prefix and tests IPv6 connectivity.
  • 可选参数 / Options: --ra-high（多路由/多 RA 环境，见下文第 3 节 / multi-router LANs, see section 3）、--force（非 PPPoE WAN / non-PPPoE WAN）、--no-ping（跳过连通性测试 / skip the connectivity test）。运行 / Run sh pcat2_pppoe_ipv6.sh --help 查看帮助。
  • 脚本源码 / Script source: GitHub Gist。中国大陆用户如无法访问 gist，请按下文手动配置。 / If the gist is unreachable from mainland China, follow the manual steps below.

中文指南

1. WAN 接口（PPPoE）

新版固件下 不需要手动创建绑定 eth0 的 WAN6 接口。只要 WAN 口开启 IPv6 协商，netifd 会自动在 PPPoE 逻辑口上创建动态别名接口 wan_6（注意是下划线），负责 DHCPv6 / 前缀委托。

LuCI: 网络 → 接口 → WAN → 高级设置

  • 获取 IPv6 地址 → 自动
  • 委托 IPv6 前缀 → 启用

或使用 UCI： 

uci set network.wan.ipv6='auto'
uci commit network
ifup wan
注意 如果系统里遗留了一个绑定 eth0 的 WAN6 接口（老指南的做法），它在 PPPoE 线路上会一直处于 pending 状态。建议直接禁用：
uci set network.wan6.auto='0'
uci commit network

2. LAN 接口

LuCI: 网络 → 接口 → LAN

  • IPv6 分配长度 (ip6assign) → 60（运营商一般下发 /56 或 /60）
  • IPv6 前缀过滤器 (ip6class) → 必须留空！
uci set network.lan.ip6assign='60'
uci -q delete network.lan.ip6class
uci commit network
ifup lan
⚠ 最常见故障 如果 ip6class 被设为 local，LAN 只会分配 ULA（fd00
:/8 私有前缀），运营商委托的公网前缀永远不会下发到 br-lan，内网设备就只有 fdxx 地址、无法访问 IPv6 互联网。删除该选项即可恢复。

3. RA / DHCPv6（SLAAC）

LuCI: 网络 → 接口 → LAN → DHCP 服务器 → IPv6 设置

  • RA 服务：混合模式 （SLAAC 默认开启，即 RA 前缀带 A 标志）
  • DHCPv6 服务：混合模式
  • NDP 代理：混合模式（旁路由/中继场景才需要）
uci set dhcp.lan.ra='hybrid'
uci set dhcp.lan.dhcpv6='hybrid'
uci commit dhcp
/etc/init.d/odhcpd reload
提示 若局域网内还有其它设备也在发 RA（多路由/多线路环境），把 photonicat 的路由优先级调高，客户端会优先选它作为默认网关：
uci set dhcp.lan.ra_preference='high'
uci commit dhcp && /etc/init.d/odhcpd reload

4. Docker 与 IPv6 转发（26.04 版重要坑）

photonicatWrt 自带 Docker（27.x）。Docker 27+ 默认启用 ip6tables，会创建 ip6 filter FORWARD 链且策略为 drop —— 它会丢弃所有转发的 IPv6 流量，即使 fw4 防火墙已放行 lan→wan。症状：路由器本机 ping6 正常，内网设备拿到了公网 IPv6 却 ping 不通外网。

检查： 

nft list chain ip6 filter FORWARD
# 如果看到 policy drop 且计数一直增长，即中招

永久修复：在 /etc/docker/daemon.json 的出厂内容基础上加一行 "ip6tables": false（不影响 IPv4 容器网络）： 

cat > /etc/docker/daemon.json <<'EOF'
{
"data-root": "/opt/",
"log-level": "warn",
"ip6tables": false
}
EOF
/etc/init.d/docker restart
⚠ 注意 photonicatWrt 实际由 /etc/init.d/docker（而非 dockerd）以 --iptables=false 参数启动 Docker。不要在 daemon.json 里添加 "iptables" 键，也不要改动出厂的 data-root —— 与启动参数冲突会导致 Docker 开机无法启动，改 data-root 会导致已有镜像"消失"。详见 Photonicat 2 Docker 使用指南。

5. 防火墙

fw4 默认已放行 lan→wan 的 IPv6 转发和必要的 ICMPv6，出站上网无需额外规则。只有当你需要从公网主动访问内网设备（自建服务器/NAS）时才添加入站规则，且建议按端口精确放行，不要整段 ACCEPT 全部入站 IPv6。

6. 验证

路由器上： 

ifstatus wan_6 | grep -A6 ipv6-prefix     # 应看到运营商委托的 /56 或 /60
ifstatus lan | grep -A8 ipv6-prefix-assignment   # 应看到公网前缀已分配给 br-lan
ping -6 -c3 photonicat.com

内网设备上： 

ip -6 addr show   # 应有公网 (如 240e:/2408:/2409: 等) SLAAC 地址
ping -6 -c3 photonicat.com

7. 多出口/多 RA 环境排障

如果局域网里有多台设备宣告 RA（例如另一台 5G 网关、Proxmox 虚拟机等），Linux 客户端会把多个默认网关做 ECMP 负载均衡，流量可能被分到没有 IPv6 上行的网关而间歇性丢包；或者源地址选择与网关不匹配（photonicat 的默认路由是按源前缀限定的 from 240e:xxxx::/56），返回 "Destination unreachable: No route"。

  • 首选：让没有上行的设备停止宣告默认路由（router lifetime 设为 0）。
  • 客户端（systemd-networkd）也可固定网关并用地址标签固定源地址选择：
# /etc/systemd/network/eth0.network.d/50-ipv6-gateway.conf
[IPv6AcceptRA]
UseGateway=false

[Route]
Gateway=fe80::xxxx:xxxx:xxxx:xxxx   # photonicat br-lan 的链路本地地址

[IPv6AddressLabel]
Label=99
Prefix=2409::/16    # 不希望选为源地址的运营商前缀

English Guide

1. WAN interface (PPPoE)

On current firmware you no longer need a manual WAN6 interface bound to eth0. With IPv6 negotiation enabled on WAN, netifd automatically spawns a dynamic alias interface wan_6 (with an underscore) on the PPPoE logical interface, which handles DHCPv6 and prefix delegation.

LuCI: Network → Interfaces → WAN → Advanced

  • Obtain IPv6 address → Automatic
  • Delegate IPv6 prefix → Enabled

Or via UCI: 

uci set network.wan.ipv6='auto'
uci commit network
ifup wan
Note If a legacy WAN6 interface bound to eth0 exists (as older guides suggested), it will sit in "pending" forever on a PPPoE line. Disable it
uci set network.wan6.auto='0'
uci commit network

2. LAN interface

  • IPv6 assignment length (ip6assign) → 60 (ISPs typically delegate a /56 or /60)
  • IPv6 prefix filter (ip6class) → must be left EMPTY!
uci set network.lan.ip6assign='60'
uci -q delete network.lan.ip6class
uci commit network
ifup lan
⚠ Most common failure If ip6class is set to local, the LAN only gets ULA (fd00
:/8) prefixes — the ISP-delegated global prefix is never assigned to br-lan, so clients only get fdxx addresses and cannot reach the IPv6 internet. Deleting this option fixes it.

3. RA / DHCPv6 (SLAAC)

  • RA-Service: hybrid (SLAAC is on by default — RA prefixes carry the A flag)
  • DHCPv6-Service: hybrid
  • NDP-Proxy: hybrid (only needed for relay/bridge setups)
uci set dhcp.lan.ra='hybrid'
uci set dhcp.lan.dhcpv6='hybrid'
uci commit dhcp
/etc/init.d/odhcpd reload
Tip If other devices on the LAN also send RAs (multi-router / multi-uplink environments), raise the photonicat's router preference so clients prefer it as default gateway
uci set dhcp.lan.ra_preference='high'
uci commit dhcp && /etc/init.d/odhcpd reload

4. Docker vs IPv6 forwarding (important 26.04 pitfall)

photonicatWrt ships Docker (27.x). Docker 27+ enables ip6tables by default and creates an ip6 filter FORWARD chain with policy drop — it silently drops all forwarded IPv6, even though fw4 correctly allows lan→wan. Symptom: ping6 works from the router itself, LAN clients get global IPv6 addresses but cannot reach the internet.

Check: 

nft list chain ip6 filter FORWARD
# if you see "policy drop" and a growing counter, this is your problem

Permanent fix: add "ip6tables": false to /etc/docker/daemon.json while keeping the factory keys (IPv4 container networking is unaffected): 

cat > /etc/docker/daemon.json <<'EOF'
{
"data-root": "/opt/",
"log-level": "warn",
"ip6tables": false
}
EOF
/etc/init.d/docker restart
⚠ Note On photonicatWrt, Docker is actually launched by /etc/init.d/docker (not dockerd) with --iptables=false. Do not add an "iptables" key to daemon.json and do not change the factory data-root — a flag/config conflict prevents Docker from starting at boot, and a changed data-root makes existing images "disappear". See Photonicat 2 Docker 使用指南.

5. Firewall

fw4 already allows IPv6 lan→wan forwarding and the required ICMPv6 by default — no extra rules are needed for outbound connectivity. Only add inbound rules when you need to reach LAN devices from the internet (self-hosted servers/NAS), and prefer precise per-port rules over a blanket ACCEPT of all inbound IPv6.

6. Verification

On the router: 

ifstatus wan_6 | grep -A6 ipv6-prefix     # ISP-delegated /56 or /60 should appear
ifstatus lan | grep -A8 ipv6-prefix-assignment   # the global prefix should be assigned to br-lan
ping -6 -c3 photonicat.com

On a LAN client: 

ip -6 addr show   # expect a global (e.g. 240e:/2408:/2409:) SLAAC address
ping -6 -c3 photonicat.com

If several devices advertise RAs on the LAN (another 5G gateway, Proxmox VMs, …), Linux clients install an ECMP default route across all of them; flows hashed to a gateway without IPv6 upstream blackhole intermittently. Source-address selection can also mismatch the gateway (the photonicat's upstream default route is source-restricted, e.g. from 240e:xxxx::/56), yielding "Destination unreachable: No route".

  • Preferred fix: make routers without upstream stop advertising a default route (router lifetime 0).
  • On a systemd-networkd client you can pin the gateway and steer source selection:
# /etc/systemd/network/eth0.network.d/50-ipv6-gateway.conf
[IPv6AcceptRA]
UseGateway=false

[Route]
Gateway=fe80::xxxx:xxxx:xxxx:xxxx   # photonicat br-lan link-local address

[IPv6AddressLabel]
Label=99
Prefix=2409::/16    # ISP prefix you do NOT want chosen as source

IPv6 地址说明 / Understanding the addresses

一个接口同时拥有多个 IPv6 地址是正常现象 / Multiple IPv6 addresses on one interface is normal:

  • 240e:xxxx:xxxx:xx00:xxxx:xxff:fexx:xxxx/64 → 公网地址，SLAAC 由 RA 前缀+接口标识自动生成 / global address, auto-generated via SLAAC
  • 240e:xxxx:xxxx:xx00::2e9/128 → DHCPv6 下发的公网地址 / global address assigned by stateful DHCPv6
  • fdxx:....../64 → ULA 私有地址，仅内网使用，不上公网 / ULA private address, LAN-only
  • fe80::/64 → 链路本地地址，用于邻居发现/网关 / link-local, used for NDP and as gateway

只有 global (GUA) 地址可用于公网通信；“全球直连”意味着设备在公网可见，请合理配置防火墙。 / Only GUA addresses reach the internet; being globally reachable means you should keep the firewall sensible.

检索自“https://photonicat.com/index.php?title=Photoincat_2_IPv6_PPPoE&oldid=923”